ON THE WEAR MECHANISM OF CARDAN GEAR JOINTS

Authors

  • Alexander Vitalievich Poprykailo JSC "Belcard"
  • Gennady Alexandrovich Costykovich JSC "Belcard"
  • Andrei Ivanovich Verameichyk Brest State Technical University https://orcid.org/0000-0003-0373-482X
  • Evgeny Vitalievich Auchynnikau Grodno State University named after Ya. Kupala
  • Vitaly Mikhailovich Khvisevich Brest State Technical University
  • Sergey Romanovich Onysko Brest State Technical University

DOI:

https://doi.org/10.36773/1818-1112-2022-129-3-31-33

Keywords:

design, cardan shaft, wear, friction, materials

Abstract

In connection with the improvement of vehicles, power plants, an increase in their power, operational life, requirements for reliability and safety of use necessitate the development of new modifications of the main components and assemblies, incl. drive shafts. In this paper, an analysis of the main types of wear of cardan gears operating in various conditions is carried out. It is shown that the main types of wear of universal joints are: fatigue and abrasive wear, false brinelling, pitting, fretting. To reduce the effect of these types of wear, a comprehensive approach has been proposed, which consists in the development of highly effective methods for hardening the working surfaces of parts, the creation of thin-film composite coatings for friction parts, the development of new compositions of new generation lubricants based on mineral and synthetic oils.

Author Biographies

Alexander Vitalievich Poprykailo, JSC "Belcard"

Chief Technologist of JSC "Belkard" for development, Grodno, Republic of Belarus.

Gennady Alexandrovich Costykovich, JSC "Belcard"

Ph.D in Engineering, Professor of the Department of Materials Science and Resource-Saving Technologies, Grodno State University named after Ya. Kupala. Deputy Director of JSC "Belcard" for Development, Grodno, Republic of Belarus.

Andrei Ivanovich Verameichyk, Brest State Technical University

Ph.D in Physics and Mathematics, Associate Professor, Senior Research Associate of Brest State Technical University Testing Center, Brest, Republic of Belarus.

Evgeny Vitalievich Auchynnikau, Grodno State University named after Ya. Kupala

Doctor of Technical Sciences, Associate Professor, Associate Professor of the Department of Logistics and Management Methods, Grodno State University named after Y. Kupala, Grodno,  Republic of Belarus.

Vitaly Mikhailovich Khvisevich, Brest State Technical University

Ph.D in Engineering, Associate Professor, Professor of the Department of Applied Mechanics, Brest State Technical University, Brest, Republic of Belarus.

Sergey Romanovich Onysko, Brest State Technical University

Ph.D in Engineering, Dean of the Faculty of Mechanical Engineering of Brest State Technical University, Brest, Republic of Belarus.

Downloads

Published

2022-11-25

How to Cite

(1)
Poprykailo, A. V.; Costykovich, G. A.; Verameichyk, A. I.; Auchynnikau, E. V.; Khvisevich, V. M.; Onysko, S. R. ON THE WEAR MECHANISM OF CARDAN GEAR JOINTS. Вестник БрГТУ 2022, 31-33.

Issue

No. 3(129) (2022): Vestnik of Brest State Technical University

Section

Mechanical Engineering

License

Copyright (c) 2022 Brest State Technical University

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

The work is provided under the terms of Creative Commons public license Attribution-NonCommercial 4.0 International (CC BY-NC 4.0). This license allows an unlimited number of persons to reproduce and share the Licensed Material in all media and formats. Any use of the Licensed Material shall contain an identification of its Creator(s) and must be for non-commercial purposes only. Users may not prevent other individuals from taking any actions allowed by the license.

Most read articles by the same author(s)