MODELING OF THE TECHNOLOGICAL PROCESS OF BENDING SHEET PARTS AT THE STAGE OF DESIGNING STAMPING EQUIPMENT

Authors

  • Victor Nikolaevich Klochkov JSC “Mogilev Elevator Engineering Plant”
  • Maksim Eduardovich Podymako JSC “Mogilev Elevator Engineering Plant”
  • Igor Aleksandrovich Kolesov JSC “Mogilev Elevator Engineering Plant”

DOI:

https://doi.org/10.36773/1818-1112-2024-134-2-98-103

Keywords:

stamping equipment, Johnson-Cook model, guide fastening, cold forming

Abstract

The article discusses an approach to modeling cold stamping of sheet materials using a specific example. A step-by-step implementation of the modeling process was carried out, which made it possible to determine the geometry of the workpiece, equipment parameters, and the amount of stamp stroke. Based on the Johnson-Cook phenomenological constitutive model, the damage integrity of sheet material was assessed.

Author Biographies

Victor Nikolaevich Klochkov, JSC “Mogilev Elevator Engineering Plant”

Head of the Reliability Bureau of the Industry Laboratory of the Scientific and Technical Center of JSC Mogilevliftmash, Mogilev, Republic of Belarus.

Maksim Eduardovich Podymako, JSC “Mogilev Elevator Engineering Plant”

Head of the industry laboratory of the scientific and technical center of JSC Mogilevliftmash, Mogilev, Republic of Belarus.

Igor Aleksandrovich Kolesov, JSC “Mogilev Elevator Engineering Plant”

Leading engineer-technologist of JSC Mogilevliftmash, Mogilev, Republic of Belarus.

References

Выбор конструкции детали как определяющий фактор технологичности и себестоимости ее изготовления на примере деталей ограничителя скорости лифта, получаемых лазерной резкой вместо их отливки с последующей механической обработкой / Т. В. Лапцевич [и др.] // Вестник Белорусско-Российского университета. – 2022. – № 3(76). – С. 52–59. – https://doi.org/10.53078/20778481_2022_3_52. – EDN: GBNYMV.

Schäfer, M. Computational Engineering – Introduction to Numerical Methods / Michael Schäfer. – Springer-Verlag Berlin Heidelberg, 2006. – 321 p.

Gomah, M. An Experimental and Numerical Investigation of an Improved Shearing Process with Different Punch Characteristics / Mahmod Gomah, Murat Demiral // Strojniški vestnik – Journal of Mechanical Engineering. – 2020. – Vol. 66, Iss. 6. – P. 375–384.

Методические принципы проектирования кронштейнов крепления лифтовых направляющих / В. Н. Клочков [и др.] // Актуальные вопросы машиноведения. – 2022. – Т. 11. – С. 74–79. – EDN: DAQDMI.

Downloads

Published

2024-07-19

How to Cite

(1)
Klochkov, V. N.; Podymako, M. E.; Kolesov, I. A. MODELING OF THE TECHNOLOGICAL PROCESS OF BENDING SHEET PARTS AT THE STAGE OF DESIGNING STAMPING EQUIPMENT. Вестник БрГТУ 2024, 98-103.

Issue

No. 2(134) (2024): Vestnik of Brest State Technical University

Section

Mechanical Engineering

License

Copyright (c) 2024 Brest State Technical University

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

The work is provided under the terms of Creative Commons public license Attribution-NonCommercial 4.0 International (CC BY-NC 4.0). This license allows an unlimited number of persons to reproduce and share the Licensed Material in all media and formats. Any use of the Licensed Material shall contain an identification of its Creator(s) and must be for non-commercial purposes only. Users may not prevent other individuals from taking any actions allowed by the license.